Moving Light Controls
This is going to be a simple lesson. One for you to come back to and say, “How do I do that again?”
Depending on your fixture, you could have a lot of parameters. A small fogger might only have two – amount of fog and fan speed. A simple LED light might only have three – red, green, blue. But a fancy moving light could have 20, 30, even 60 parameters. It would be silly to create a screen for each of these parameters; so instead, EOS creates a few flexible screens for you to interact with.
You’ve already dealt with the color picker, the next is called the Moving Lights display, or ML Controls in the tabs.
If you don’t have any channels selected, this display will just be a big black box. But if you click on a channel in the Live Table or selected a channel in the command line (i.e. [4] [Enter]). You’ll see all the possible parameters; organized in a standard group of Moving Light categories – Intensity, Focus, Color, Form, Image, and Shutter. Clicking on the yellow category button on the left will scroll the window down to the controls for that category.
The first, and perhaps the most important button you’ll see is the one that looks like a little house – this is the [Home] button. These exist for every parameter, every category, and even the entire fixture. This will set the fixture’s parameters back to the home values and release control. This is similar to the sneak command. Try it out by brining channel 4 to full and choosing a color from ML color picker. Next press the [Home] button above the red parameter; which will leave the values for blue and green. Next try to press the [Home] button under the color category; this will release the red, green, and blue values. Finally, press the [Home] button at the way left, which will sneak all values – this time intensity is the only one remaining.
The next thing I’d like you to see are the wheels. This is virtual representation of a physical scrolling wheel that you might find on a large, physical light board. Here you can either click, click and hold, or drag the wheel. Depending on how far above or below you are from the center line, the values will increase or decrease in small or large increments. But personally, I like to use my mouse wheel (or trackpad scrolling) to scroll the wheel up or down. Simply hover your cursor over the wheel and scroll away! Try it out by selecting channel 4 and scrolling up the intensity. Wheels also have a [Min] button, which will bring the parameter to its minimum value and a [Max] button, which will bring the parameter to its maximum value. Try it out with channel 4’s intensity. Min will bring it to 0%. Max will bring it to Full.
Another way a fixture might interact with EOS is by using option buttons. This is a way for the light board to display various options available and unique to the fixture itself. Select channel 4, set it to full, and press the [Form] button which will scroll you to the bottom of the window. Pressing the “Strobe 0 to 10 Hz” button will turn up the scroll wheel to a value of 5 and start the fixture flashing. You could then scroll the wheel to create a different frequency of strobe. Pressing the “Open” button will then restore the the strobe to its always on state (you could also press the [Home] button).
Other buttons are truly unique the fixture and have no visual representation in Augment3d. For example, channel 4 has a “Color Mix 2” option. If you were to selected something like “Auto 3”, the light seems to stay white and not change at all; however, if you had the actual lighting sitting in front of you it would be constantly changing color. This is because the light knows what it’s supposed to do in “Auto 3” mode, but EOS doesn’t. These can be largely ignored in visualization and should be used only in real life.
One more tip / trick to help visualize your ML Controls. Sometimes you don’t care to see a certain feature set / category of a moving light. Clicking in the [-] button under any category will minimize its controls. Click the button again (which now looks like a box) to maximize the controls. Here, for example, I’ve minimized all the categories except for Intensity.
We’ll talk about the other options you might find in the ML Controls in the next few lessons; but for now, here’s one last little tidbit …
Unless you’re doing a lot of working with specific features of an intelligent fixture, you might not want to use all that screen space to always show the ML Controls display. In this case you could use the ML Controls popup. This can be found in the top, right corner of the screen by clicking on the little icon that looks like beams of light; found next to the Virtual Keyboard popup button and the Magic Sheet popup button.